Establishing National
Standards for Power Engineers.
Stator Replacement and Maintenance
Recently, American Society of Power Engineers (ASOPE®) documented the process of maintenance and component replacement on a 650 mw General Electric unit. Units of these kind are commonly used in steam power generation applications. The generator required a variety of inspections and maintenance to ensure it was to spec and ready for use in the field.
For this particular GE generator, the primary focus was the maintenance of stator windings. The most common failure of these windings are loose stator bars in slots, stator bar insulation deterioration, and thermal cycling. A licensed ASOPE® Power Engineer has the training and expertise to correctly maintain these types of generators and properly inspect, replace, and repurpose stator windings and bars. Provided are photos and descriptions of the process used by a licensed ASOPE® Power Engineer to properly get this generator back in the field.
Disassembly begins on
stator bar replacement
Undoing the brazing of the
bars and loop leaves.
Removal of ripple springs from between the bar and core iron.
Cutting and removing
core slot wedges.
Carefully removing top bars.
Top bar removal from
turbine end of generator.
All 18 top bars and
bottom bar #33 removed.
18 top bars ready for inspection test.
Four top bars to be
reused after Hi Pot test.
Prepping suppressor
areas on original bars.
Repair slot section armor tape on original bars.
Stator core slot section inspection prior to bar assembly.
End windings cleaned and prepared for bar assembly.
New bottom bar installed in slot #33.
New top bar install.
Final bar installed.
Assembling and
brazing bar clip leaves.
Plumbing cleaned and
prepared for assembly.
Inspection of epoxy
injection after leaf brazing.
Inspection of new epoxy injection clips for final install.
Recording clip internal
inspection on video.
Epoxy injection completed.
Baking of clips begins.
Pressurizing with Helium to check epoxy injection integrity.
Piping assembled and brazed.
Leak at bar #20 found in plumbing, repaired and rebrazed.
Mica tape on series loops CE.
Assembling nose rings.
Ultrasonic test performed
during flush operations.
Stator wings baked at
100 deg C for 12 hours.
Disconnecting and grounding RTD's.
Assembling core slot wedges.
Flux probe re-installation.
Tying bar and tension member
ties in end windings.
End windings completely
blocked and tied.
Applying flooding resin
epoxy to coat end windings.
Inner End Shield in place ready for field.
Recently, American Society of Power Engineers (ASOPE®) documented the process of maintenance and component replacement on a 650 mw General Electric unit. Units of these kind are commonly used in steam power generation applications. The generator required a variety of inspections and maintenance to ensure it was to spec and ready for use in the field.
For this particular GE generator, the primary focus was the maintenance of stator windings. The most common failure of these windings are loose stator bars in slots, stator bar insulation deterioration, and thermal cycling. A licensed ASOPE® Power Engineer has the training and expertise to correctly maintain these types of generators and properly inspect, replace, and repurpose stator windings and bars. Provided are photos and descriptions of the process used by a licensed ASOPE® Power Engineer to properly get this generator back in the field.
|
Disassembly begins on |
Undoing the brazing of the |
Removal of ripple springs from between the bar and core iron.
|
|
Cutting and removing |
Carefully removing top bars. |
Top bar removal from |
|
All 18 top bars and |
18 top bars ready for inspection test. |
Four top bars to be |
|
Prepping suppressor |
Repair slot section armor tape on original bars. |
Stator core slot section inspection prior to bar assembly. |
|
End windings cleaned and prepared for bar assembly. |
New bottom bar installed in slot #33. |
New top bar install. |
|
Final bar installed. |
Assembling and |
Plumbing cleaned and |
|
Inspection of epoxy |
Inspection of new epoxy injection clips for final install. |
Recording clip internal |
|
Epoxy injection completed. |
Pressurizing with Helium to check epoxy injection integrity. |
Piping assembled and brazed. |
|
Leak at bar #20 found in plumbing, repaired and rebrazed. |
Mica tape on series loops CE. |
Assembling nose rings. |
|
Ultrasonic test performed |
Stator wings baked at |
Disconnecting and grounding RTD's. |
|
Assembling core slot wedges. |
Flux probe re-installation. |
Tying bar and tension member |
|
End windings completely |
Applying flooding resin |
Inner End Shield in place ready for field. |